熱線： |
400-6064-114 |
電話： |
021-51863849 |
傳真： |
021-59775509 |
企業QQ |
274135888 |
企業
郵箱 |
wj@bengfawj.com
bengfawj@163.com |
地址： |
上海市青浦區華新鎮蘆蔡北路1233弄98號 |
網址： |
www.blt8888.cn |
|
磁力泵的特點 |
1．永磁體
1. Magnets
由稀土永磁材料制成的永磁體工作溫度范圍廣(-45－400℃)，矯頑力高，磁場方向具有很好的各向異性，在同極相接近時也不會發生退磁現象，是一種很好的磁場源。
From the rare-earth permanent magnetic materials, permanent magnet made of a wide range of body temperature (-45-400 ℃), high coercivity, magnetic anisotropy direction has a very good, with a very similar demagnetization does not occur when approaching the phenomenon of is a good source of the magnetic field.
2.隔離套
2. Isolation sets
在采用金屬隔離套時，隔離套處于一個正弦交變的磁場中，在垂直于磁力線方向的截面上感應出渦電流并轉化成熱量。渦流的表達式為： 。其中Pe－渦流；K—常數；n—泵的額定轉速；T－磁傳動力矩；F－隔套內的壓力；D－隔套內徑； 一材料的電阻率； —材料的抗拉強度。當泵設計好后，n、T是工況給定的，要降低渦流只能從F、D、 、 等方面考慮。選用高電阻率、高強度的非金屬材料制作隔離套，在降低渦流方面效果十分明顯。
Sets in when the metal isolation, isolation sets in a sinusoidal alternating magnetic fields, in the direction perpendicular to the magnetic field lines out of the cross section induced eddy currents and transformed into heat. Swirl in the expression as follows:. Where Pe-eddy; K-constant; n-pump rated speed; T-magnetic driving torque; F-compartment comprising the pressure; D-separated sets of diameter; a material resistivity; - tensile strength of materials. When the pump design is getting better, n, T is the given conditions, to reduce eddy current only from F, D,, and other considerations. Use of high resistivity, high-strength non-metallic material isolated sets of results in reducing the eddy current context is very obvious.
3．冷卻潤滑液流量的控制
3. Lubrication Liquid Flow Control
泵運轉時，必須用少量的液體對內磁轉子與隔離套之間的環隙區域和滑動軸承的摩擦副進行沖洗冷卻。冷卻液的流量通常為泵設計流量的2%-3%，內磁轉子與隔離套之間的環隙區域由于渦流而產生高熱量。當冷卻潤滑液不夠或沖洗孔不暢、堵塞時，將導致介質溫度高于永磁體的工作溫度，使內磁轉子逐步失去磁性，使磁力傳動器失效。當介質為水或水基液時，可使環隙區域的溫升維持在3-5℃；當介質為烴或油時，可使環隙區域的溫升維持在5-8℃。
Pump running, you must use a small amount of fluid set of internal magnetic separation between the rotor and the annulus area and sliding friction bearings for flushing cooling deputy. The flow of coolant pump design flow is usually 2% -3%, within a set of magnetic separation between the rotor and the annulus region due to eddy current arising from high-calorie. When the cooling lubricant inadequate or poor flushing holes to plug, it will lead to medium temperature is higher than the operating temperature permanent magnets, so that the gradual loss of magnetic properties within a magnetic rotor, so that magnetic transmission failure. When the medium is water or water-based fluid, the annulus region temperature can be maintained at 3-5 ℃; when the medium is hydrocarbon or oil when the temperature rise can annulus region maintained at 5-8 ℃.
4．滑動軸承
4. Bearing
磁力泵滑動軸承的材料有浸漬石墨、填充聚四氟乙烯、工程陶瓷等。由于工程陶瓷具有很好的耐熱、耐腐蝕、耐摩擦性能，所以磁力泵的滑動軸承多采用工程陶瓷制作。由于工程陶瓷很脆且膨脹系數小，所以軸承間隙不得過小，以免發生抱軸事故。
Magnetic pump sliding bearing materials impregnated graphite, PTFE and engineering ceramics. As the engineering ceramics have good heat resistance, corrosion, rubbing performance, so the sliding bearing magnetic pump to use more production of engineering ceramics. As the engineering ceramics is very crisp and the expansion coefficient is small, so bearing clearance shall not be too small to hold shaft in order to avoid an accident.
由于磁力泵的滑動軸承以所輸送的介質進行潤滑，所以應根據不同的介質及使用工況，選用不同的材質制作軸承。
As the magnetic pump to the sliding bearing lubrication delivery media, it should be according to different media and the use of working conditions, use of different materials produced bearings.
5．保護措施
5. Protection
當磁力傳動器的從動部件在過載情況下運行或轉子卡死時，磁力傳動器的主、從動部件會自動滑脫，保護機泵。此時磁力傳動器上的永磁體在主動轉子交變磁場的作用下，將產生渦損、磁損，造成永磁體溫度升高，磁力傳動器滑脫失效。
When the magnetic actuator of the slave parts in case of overload operation or rotor stuck, the magnetic actuator of the master, slave components will automatically slip to protect pump. At this point magnetic actuator in an active permanent magnet on the rotor under the action of alternating magnetic field will produce eddy loss, magnetic loss, resulting in permanent magnet temperature, magnetic transmission slip failure. |
|
|
